Kenton Memorymoog (after June 06) Instrukcja Użytkownika Pobierz pdf

User instructions for Kenton MIDI retrofit for

MEMORYMOOG

These instructions are only for Memorymoog MIDI retrofit kits produced after 1

June 2006

Firmware MEMM5100 or later.

N.B. Different instructions apply to earlier Kenton Memorymoog MIDI retrofit kits.

USING THE MIDI INTERFACE

When you turn on the synthesizer for the first time, you will be in omni-off mode channel 1 for receive and also

channel 1 for transmit - See the following pages for other factory default settings. When you select a transmit or

receive channel, this will be stored in memory and will be remembered for when you subsequently turn on the synth

- all parameters listed on the next page are stored.

If you want to put the machine back to the factory default settings at any time, switch the synth on whilst holding the

red push button pressed - hold for a couple of seconds then release.

RED PUSH BUTTON

Three modes are available by pushing the red push button during normal playing mode. Before you press the red

button however, make sure that no keys are pressed on either the Memorymoog or the remote MIDI keyboard

otherwise the results may be unpredictable. The key presses can be entered on the Memorymoog’s own keyboard,

or from the remote MIDI keyboard.

1) PROGRAM CHANGE MODE

For sending program changes from the keyboard. Press the red push button once only (short press – then release).

Any key then selects a program change which it sends through the MIDI Out. When the key is released, you are

then automatically returned to playing mode. For example a short press on the red push button followed by bottom

C will send program change #0 whereas top C will send #60. (Nothing is stored in non-volatile memory after this

operation)

2) SET-UP MODE

For setting MIDI channels and assignments. Give the red push button two short presses (half a second each) - then

release. Follow this with a key or sequence of keys as detailed on page 2. After making a MIDI channel assignment,

you will be automatically returned to playing mode but after making other assignments you will need to press the

ENTER key (Top C) to return to playing mode. This is to enable you to make the multiple key presses required

when re-assigning Sources to Destinations. (N.B. all set-ups are stored in non volatile memory).

3) TRANSPOSE MODE

Press and hold the red push button for about four seconds - then release. Middle C will sound on the synth and

continue to sound until you press a key. The key that you press will be the new middle C for MIDI IN. You can set

any value up to two octaves up or down - settings outside this range will be ignored. Both MIDI in and MIDI out will

be transposed by the same value. Note that transpose mode cannot be entered from set-up mode. (N.B. the

transposition will be stored in non volatile memory).

1 2 3 4

MEMORYMOOG 1

Podsumowanie treści

Strona 1 - MEMORYMOOG

User instructions for Kenton MIDI retrofit for MEMORYMOOG These instructions are only for Memorymoog MIDI retrofit kits produced after 1st June

Strona 2

Function of keys during set-up mode: C Receive channel 1 (default) [ Bottom C - MIDI note #36 ] Db " " 2 D "

Strona 3

ASSIGNING MIDI CONTROL SOURCES TO DESTINATIONS SOURCE DEFAULT DESTINATION Pitch-bend wheel Pitch-bend Modulation wheel (cc#1) Mod

Strona 4

11) For transmit key velocity (ON or OFF), keep pressing the increase or decrease key and listen at the device attached to the MIDI OUT until

Powiązane modele: Memorymoog

Komentarze do niniejszej Instrukcji

Brak uwag

Kenton Memorymoog (after June 06) Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Ekwipunek Kenton Memorymoog (after June 06). Kenton Memorymoog (after June 06) User Manual [en] [pl] [cs] [de] Instrukcja obsługi

Podsumowanie treści

Powiązane modele: Memorymoog

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Kenton Memorymoog (after June 06)